Lifting Clamps

CG Heavy Duty Girder Clamp

The Girder Clamp has been designed to meet the requirements of the heavy steel industry where the handling of larger sizes of beams presents a problem. It incorporates a positive lock on to one of the uppermost edges which will allow the beam to be set down with the web or flange vertical.

Click Here for Specification Sheet


CH Heavy Duty Horizontal Plate Clamp

Used in pairs this range of clamps is ideal for loading machines and moving plate material in the horizontal position. A single pair of clamps fitted to a two leg chain sling (maximum sling angle 90) is all that is required for lifting short lengths of plate. For long plates, 2 pairs of clamps suspended by chain from a lifting beam must be used. The two jaws and wide toe plate give the clamp a stable grip on the plate. The integral shackle ring will accept chain sling hooks or wire rope slings directly.

Click Here for Specification Sheet


CH Heavy Duty Horizontal Plate Clamp

Used in pairs this range of clamps is ideal for loading machines and moving plate material in the horizontal position. A single pair of clamps fitted to a two leg chain sling (maximum sling angle 90) is all that is required for lifting short lengths of plate. For long plates, 2 pairs of clamps suspended by chain from a lifting beam must be used. The two jaws and wide toe plate give the clamp a stable grip on the plate. The integral shackle ring will accept chain sling hooks or wire rope slings directly.

Click Here for Specification Sheet


CP Pile Pitching Clamp


CR Rail Lifting Clamp

For handling rail sections. These clamps are designed to lift most sizes of rail now in use in the USA.

Click Here for Specification Sheet


CT Heavy Duty T or Channel Section Clamp

  • Specially designed for shipbuilding applications. Available with either standard hookring for use with existing sling hook, or with integral short chain sling for direct fitting on to the crane hook.
  • All clamps fitted with locking mechanism.

Click Here for Specification Sheet


CX Heavy Duty Hinged Universal Plate Clamp

  • The CX Hinged Universal Plate Clamp has been developed especially for the handling of plate at any angle thus permitting the awkward lifts previously considered hazardous.
  • The CX clamp is particularly suitable for handling
    fabrications because of the facility of the lifting eye
    and link.
  • Suitable for all structural steel up to 300 Brinell surface hardness.

Click Here for Specification Sheet


CY Hinged Universal Plate Clamp

  • The new CY clamp is based on our successful 92 series range of clamps and incorporates the new universal hinged hookring.
  • The CY Hinged Universal Plate Clamp has been developed especially for the handling of plate at any angle thus permitting the awkward lifts previously considered hazardous.
  • Suitable for all structural steel up to 300 Brinell surface hardness.

Click Here for Specification Sheet


CZ92 Universal Plate Clamp

  • Lift and turn over plates in one smooth operation.
  • Plates can be turned over or lifted from the horizontal to the true vertical position.
  • Available with either standard hookring for use with existing sling hook, or with integral short chain sling for direct fitting on to the crane hook.
  • Hardened steel jaws for positive grip and locking mechanism.
  • Suitable for all structural steel up to 300 Brinell surface hardness.

Click Here for Specification Sheet


GS Girder Stacking Clamp

Specifically designed for the handling of rolled steel beams and joists when stacked horizontally. The unique design enables the beam to be lifted by one flange and transported horizontally.

Click Here for Specification Sheet


HG High Grip Clamp

  • These clamps develop a much higher grip on the lifted plate and are complementary to the Universal type. They are particularly suitable for lifting plates with hardened surfaces or stainless steel.
  • Available with either standard hookring for use with existing sling hook, or with integral short chain sling for direct fitting on to the crane hook.
  • Suitable for all structural steel up to 376 Brinell surface hardness.

Click Here for Specification Sheet


Heavy Duty Hoist Rings

  • Back and side pins constructed of one piece forged alloy steel
  • Less moving parts than competitive rings
  • Bale and center body are closed die forged to assure superior grain flow and consistent dimensional accuracy
  • 100% magnetic particle inspected
  • Patented product specified in wide range of industries
  • Larger bale allows use of a variety of hook sizes
  • Easy disassembly for periodic non-destructive inspection
  • Capacities range from 800-24,000 Ibs.
  • Economically priced

Click Here for Specification Sheet


LJ Gentle Grip Clamp

The jaws of this clamp are lined with chrome leather. Each clamp should be inspected weekly to check for wear to the jaw lining. DO NOT use solvents to clean the jaw lining as this may affect the bond between the surface material and the metal of the jaw.

The LJ range of clamps is specifically designed to lift plate without marking or damaging the surface finish. They are particularly suitable for lifting thin gauge steel plate, stainless steel and aluminium plate. The clamp jaws are lined with chrome leather. The clamp is also suitable for use with steel of a hardness above 300 Brinell, e.g. 'Hardox.' See operating instructions for maintenance of soft jaws.

Click Here for Specification Sheet


PP Pile Pulling Clamp

The Pile Pulling Clamp is designed to pull out driven piles. The clamp has a narrow opening and deeper slot to ensure pile is gripped firmly.

It is extremely difficult to determine the forces required to pull out a driven pile, contractors should therefore take extra care to ensure that the WLL of the clamp is not exceeded. Lifting appliances should preferably be fitted with a load indicator.

Click Here for Specification Sheet


RH Roller Toe Horizontal Clamp

The contact area features a roller toe to assist correct location, and allows reduced marking during lifting.

Click Here for Specification Sheet


SC92T Twin Screwlok Clamp

The Twin Screwlok Clamps are designed to enable one beam to be suspended beneath another beam.

Click Here for Specification Sheet


SH Sheet Bundle Horizontal Clamp

  • These clamps are used in pairs on a spreader beam for lifting bundles of plates.
  • Maximum sling angle is 90.

Click Here for Specification Sheet


Screwlok Beam Clamp

  • Designed to fit flanges of most structural beams
  • Act as semi-permanent lifting point for use with manual or electric hoists
  • Shackle incorporated for load suspension
  • Imported

Click Here for Specification Sheet


Specialty Engineered Hoist Rings

  • Bale and shoulder pins machined from alloy steel
  • Patented design provides shoulder pin retention with specialized clip
  • Easy disassembly for periodic non-destructive inspection
  • Capacity range from 800-100,000 Ibs.
  • Specials available in stainless steel and metric sizes

Click Here for Specification Sheet


TBT Snap-on Trolley Clamp

  • Trolleys contain jaw openings up to 7 7/8", depending upon model selected
  • Once the load is positioned, the trolley is locked into place

Click Here for Specification Sheet


TH Wide Mouth Clamp

  • These clamps lift and turn over plates in one smooth operation.
  • Designed for lifting and handling wide loads from 0-7 7/8 inches thick. The clamp is provided with a lever
    operated opening device.

Click Here for Specification Sheet


THK Horizontal Thin Sheet Clamp

  • A horizontal plate lifting clamp with reversed jaws designed to handle thin sheets that deflect when being lifted.
  • Clamps are used in pairs.

Click Here for Specification Sheet


THS Horizontal Plate Clamp

These clamps are designed for lifting and handling sheet steel plates. The clamp is particularly useful for loading plates into guillotines, presses, punching machines and folding presses. The locking mechanism is pre-tensioned ensuring a proper grip. These clamps can be used in pairs or singly.

Click Here for Specification Sheet


TSB Wide Jaw Gentle Grip Clamp

This clamp has hard rubber lined clamping jaws for handling loads that must not be marked.

Click Here for Specification Sheet


TSC Push Travel Screwlok Trolley Clamp

The push travel Screwlok trolley clamp provides an easily moved temporary suspension point.

Click Here for Specification Sheet


TSS Gentle Grip Clamp

This clamp is specifically designed to lift without marking the surface. Particularly useful for lifting stainless steel when it is important not to impregnate the stainless steel with ferrous material.

Click Here for Specification Sheet


TTG Horizontal Girder Clamp

  • This clamp is designed to lift and transport steel beams with the flanges in a horizontal position.
  • The clamp is fitted with a locking mechanism and can be used in pairs or singly.

Click Here for Specification Sheet


TTR Girder Clamp

This clamp has been developed for handling structural beams with the flanges in a vertical position. The hookring is
designed to be as near the center of gravity as possible resulting in a near horizontal lift.

Click Here for Specification Sheet

Return

Meerholz Canada LTD
1840 1st Avenue
Prince George, B.C. V2L 2Y9
Tel: (250) 562-2788
Fax: (250) 562-2782

Copyright © 2007-2017 Meerholz Canada Ltd. All Rights Reserved.
web services by Sticky Wicket Designs